Category: Arduino

Arduino First Assignment

Night Rider

int L1 =  13;

int leds[] = {9, 10, 11, 12, 13};
int delayTimer = 100;

// The setup() method runs once, when the sketch starts

void setup()   {                
  // initialize the digital pin as an output:
  for (int i = 0; i < 6; i++)
  {
    pinMode(leds[i], OUTPUT);
  }
}

// the loop() method runs over and over again,
// as long as the Arduino has power

void loop()                    
{
  for (int i = 0; i < 6; i++)
  {
    digitalWrite(leds[i], HIGH);   // set the LED on
    delay(delayTimer);   
    digitalWrite(leds[i], LOW);
  }
}


Circuit #3

 

minnar xie: arduino: blinky LED!

[youtube http://www.youtube.com/watch?v=7DvY-IAyqgw]

 

int leds[] = {13, 12, 11, 10, 9, 8, 7, 6, 5, 4};

// The setup() method runs once, when the sketch starts

void setup(){
// initialize the digital pin as an output:
for (int i = 0; i < 10; i++){
pinMode(leds[i], OUTPUT);
}
}

// the loop() method runs over and over again,
// as long as the Arduino has power

void loop() {
for (int i = 0; i<10; i++){
digitalWrite(leds[i], HIGH); // set the LED on
delay(100);
digitalWrite(leds[i], LOW);
}

for (int i = 9; i>0; i--){
digitalWrite(leds[i], HIGH); // set the LED on
delay(100);
digitalWrite(leds[i], LOW);
}
}

Sarah Anderson- Kit’s Lights

Sarah Anderson – Kit’s Lights

[youtube http://www.youtube.com/watch?v=O9aI8FnvWSI]

int ledPins[] = {13,12,11,10,9};

void setup() {
for (int index = 0; index =0; index--){
digitalWrite(ledPins[index],HIGH);
delay(delayTime);
digitalWrite(ledPins[index],LOW);

}
}
don't know why it only shows my setup, here is the rest:

void loop(){
kitLiteR();
kitLiteL();
}
void kitLiteR(){
int delayTime=100;
for (int index =0; index<=4; index++){
digitalWrite(ledPins[index],HIGH);
delay(delayTime);
digitalWrite(ledPins[index],LOW);

}
}

void kitLiteL(){
int delayTime=100;
for (int index =4; index>=0; index–){
digitalWrite(ledPins[index],HIGH);
delay(delayTime);
digitalWrite(ledPins[index],LOW);

}
}

Knight Rider Lights–Andrea

I’m not sure how to use the plugin we’re supposed to use for this, but here is my code using some built-in tool.

/*andrea gershuny
cmu ems II, fall 2012
reproduction of KITT's flashing light pattern from Knight Rider*/

void setup() { 
// nothing happens in setup! how boring. 
}

void loop() { 
for (int i = 4; i3; j-=1){ 
  digitalWrite(j,HIGH);
  delay(100);
  digitalWrite(j,LOW);
 }
}

blinking LEDs and circuit 03

[vimeo 52050555 w=500 h=281]

blinking LEDs from Connie D on Vimeo.

int L1 = 13;    // LED connected to digital pin 13
int L2 = 12;    // LED connected to digital pin 12
int L3 = 11;    // LED connected to digital pin 11
int L4 = 10;
int L5 = 9;
int L6 = 8;
int L7 = 7;
int L8 = 6;
int L9 = 5;
int L10 = 4;

// The setup() method runs once, when the sketch starts

void setup()   {                
  // initialize the digital pin as an output:
  pinMode(L1, OUTPUT);
  pinMode(L2, OUTPUT);
  pinMode(L3, OUTPUT);
  pinMode(L4, OUTPUT);
  pinMode(L5, OUTPUT);
  pinMode(L6, OUTPUT);
  pinMode(L7, OUTPUT);
  pinMode(L8, OUTPUT);
  pinMode(L9, OUTPUT);
  pinMode(L10, OUTPUT);
}

// the loop() method runs over and over again,
// as long as the Arduino has power

void loop()                    
{
  digitalWrite(L1, HIGH);   // set the LED on
  delay(100);  // wait for a second
  digitalWrite(L1, LOW);
  digitalWrite(L2, HIGH);   // set the LED on
  delay(100);                  // wait for a second
  digitalWrite(L2, LOW);
  digitalWrite(L3, HIGH);    // set the LED off
  delay(100);   
  digitalWrite(L3, LOW);
  digitalWrite(L4, HIGH);
  delay(100);    
  digitalWrite(L4, LOW);
  digitalWrite(L5, HIGH);
  delay(100);    
  digitalWrite(L5, LOW);
  digitalWrite(L6, HIGH);
  delay(100);    
  digitalWrite(L6, LOW);
  digitalWrite(L7, HIGH);
  delay(100);    
  digitalWrite(L7, LOW);
  digitalWrite(L8, HIGH);
  delay(100);    
  digitalWrite(L8, LOW);
  digitalWrite(L9, HIGH);
  delay(100);
  digitalWrite(L9, LOW);
  digitalWrite(L10, HIGH);
  delay(100);
  digitalWrite(L10, LOW);
  digitalWrite(L9, HIGH);
  delay(100);
  digitalWrite(L9, LOW);
  digitalWrite(L8, HIGH);
  delay(100);
  digitalWrite(L8, LOW);
  digitalWrite(L7, HIGH);
  delay(100);
  digitalWrite(L7, LOW);
  digitalWrite(L6, HIGH);
  delay(100);
  digitalWrite(L6, LOW);
  digitalWrite(L5, HIGH);
  delay(100);
  digitalWrite(L5, LOW);
  digitalWrite(L4, HIGH);
  delay(100);
  digitalWrite(L4, LOW);
  digitalWrite(L3, HIGH);
  delay(100);
  digitalWrite(L3, LOW);
  digitalWrite(L2, HIGH);
  delay(100);
  digitalWrite(L2, LOW);
}

[vimeo 52050556 w=500 h=281]

circuit 03 from Connie D on Vimeo.

Arduino Knight Rider – Rosey

int L1 = 13;
int L2 = 12;
int L3 = 11;
int L4 = 10;
int L5 = 9;
int L6 = 8;
int L7 = 7;

void setup() {
pinMode(L1, OUTPUT);
pinMode(L2, OUTPUT);
pinMode(L3, OUTPUT);
pinMode(L4, OUTPUT);
pinMode(L5, OUTPUT);
pinMode(L6, OUTPUT);
pinMode(L7, OUTPUT);
}

void loop()
{
digitalWrite(L1, HIGH);
delay(100);
digitalWrite(L2, HIGH);
digitalWrite(L1, LOW);
delay (100);
digitalWrite(L3, HIGH);
digitalWrite(L2, LOW);
delay(100);
digitalWrite(L4, HIGH);
digitalWrite(L3, LOW);
delay(100);
digitalWrite(L5, HIGH);
digitalWrite(L4, LOW);
delay(100);
digitalWrite(L6, HIGH);
digitalWrite(L5, LOW);
delay(100);
digitalWrite(L7, HIGH);
digitalWrite(L6, LOW);
delay(100);
digitalWrite(L6, HIGH);
digitalWrite(L7, LOW);
delay(100);
digitalWrite(L5, HIGH);
digitalWrite(L6, LOW);
delay(100);
digitalWrite(L4, HIGH);
digitalWrite(L5, LOW);
delay(100);
digitalWrite(L3, HIGH);
digitalWrite(L4, LOW);
delay(100);
digitalWrite(L2, HIGH);
digitalWrite(L3, LOW);
delay(100);
digitalWrite(L2, LOW);
}

Blinking LEDs – Kyna

For some reason I can’t open any Adobe programs, so I couldn’t strip the sound. Sorry…
[youtube http://www.youtube.com/watch?v=tsiMpjwOWp8?rel=0]

int del = 50;

void setup(){
  // initialize the digital pin as an output.
  for(int led = 13; led > 5; led--){
    pinMode(led, OUTPUT);
  }
}
// the loop routine runs over and over again forever:
void loop() {
  for(int i = 13; i > 5; i--){
    digitalWrite(i, HIGH);
    delay(del);
    digitalWrite(i, LOW);
  }
  for(int j = 6; j < 14; j++){
    digitalWrite(j, HIGH);
    delay(del);
    digitalWrite(j, LOW);
  }
}

09c. Blinking LEDs

Remove everything from the breadboard and let’s make CIRCUIT #1

Copy the code from the manual.

Now make it blink faster!

Blinking 2 LEDs

int L1 =  13;    // LED connected to digital pin 13
int L2 =  12;    // LED connected to digital pin 12

// The setup() method runs once, when the sketch starts

void setup()   {                
  // initialize the digital pin as an output:
  pinMode(L1, OUTPUT);
  pinMode(L2, OUTPUT);
}

// the loop() method runs over and over again,
// as long as the Arduino has power

void loop()                    
{
  digitalWrite(L1, HIGH);   // set the LED on
  delay(1000);                  // wait for a second
  digitalWrite(L2, HIGH);   // set the LED on
  delay(1000);                  // wait for a second
  digitalWrite(L1, LOW);    // set the LED off
  delay(1000);                  // wait for a second
  digitalWrite(L2, LOW);    // set the LED off
  delay(1000); 
}

Make them blink at the same time and alternated.

Blinking 3 LEDs

Now 3 LEDs!

int L1 =  13;    // LED connected to digital pin 13
int L2 =  12;    // LED connected to digital pin 12
int L3 =  11;    // LED connected to digital pin 11

// The setup() method runs once, when the sketch starts

void setup()   {                
  // initialize the digital pin as an output:
  pinMode(L1, OUTPUT);
  pinMode(L2, OUTPUT);
  pinMode(L3, OUTPUT);
}

// the loop() method runs over and over again,
// as long as the Arduino has power

void loop()                    
{
  digitalWrite(L1, HIGH);   // set the LED on
  delay(1000);                  // wait for a second
  digitalWrite(L2, HIGH);   // set the LED on
  delay(1000);                  // wait for a second
  digitalWrite(L3, HIGH);    // set the LED off
  delay(1000);              // wait for a second
  digitalWrite(L1, LOW);    // set the LED off
  digitalWrite(L2, LOW);    // set the LED off
  digitalWrite(L3, LOW);    // set the LED off
  delay(1000);
}

Exercise 1.

Using all of your red LEDs, make a circuit that reproduces KITT’s flashing light pattern from Knight Rider.

Upload a video of your working circuit on YouTube and post the link on the blog. Include your Arduino code.

To upload code into the blog, we are using the WP-Syntax WordPress plugin. To embed code in your post, switch to the “HTML” view tab in the WordPress editor, and then wrap your code with the following tags:

 

 

Exercise 2

Get working “Circuit #3” (RGB LED) from the SIK GUIDE book. The code for this sketch is available at http://www.sparkfun.com/sikcode

/*
SparkFun Inventor's Kit
Example sketch 03

RGB LED

  Make an RGB LED display a rainbow of colors!

Hardware connections:

  An RGB LED is actually three LEDs (red, green, and blue) in
  one package. When you run them at different brightnesses,
  the red, green and blue mix to form new colors.

  Starting at the flattened edge of the flange on the LED,
  the pins are ordered RED, COMMON, GREEN, BLUE.

  Connect RED to a 330 Ohm resistor. Connect the other end
  of the resistor to Arduino digital pin 9.

  Connect COMMON pin to GND.

  Connect GREEN to a 330 Ohm resistor. Connect the other end
  of the resistor to Arduino digital pin 10.

  Connect BLUE to a 330 Ohm resistor. Connect the other end
  of the resistor to Arduino digital pin 11.

This sketch was written by SparkFun Electronics,
with lots of help from the Arduino community.
Visit http://learn.sparkfun.com/products/2 for SIK information.
Visit http://www.arduino.cc to learn about the Arduino.

Version 2.0 6/2012 MDG
*/

// First we'll define the pins by name to make the sketch
// easier to follow.

// Here's a new trick: putting the word "const" in front of a
// variable indicates that this is a "constant" value that will
// never change. (You don't have to do this, but if you do, the
// Arduino will give you a friendly warning if you accidentally
// try to change the value, so it's considered good form.)

const int RED_PIN = 9;
const int GREEN_PIN = 10;
const int BLUE_PIN = 11;

// This variable controls how fast we loop through the colors.
// (Try changing this to make the fading faster or slower.)

int DISPLAY_TIME = 100;  // In milliseconds

void setup()
{
  // Here we'll configure the Arduino pins we're using to
  // drive the LED to be outputs:

  pinMode(RED_PIN, OUTPUT);
  pinMode(GREEN_PIN, OUTPUT);
  pinMode(BLUE_PIN, OUTPUT);
}

void loop()
{
  // In this sketch, we'll start writing our own functions.
  // This makes the sketch easier to follow by dividing up
  // the sketch into sections, and not having everything in
  // setup() or loop().

  // We'll show you two ways to run the RGB LED.

  // The first way is to turn the individual LEDs (red, blue,
  // and green) on and off in various combinations. This gives you
  // a total of eight colors (if you count "black" as a color).

  // We've written a function called mainColors() that steps
  // through all eight of these colors. We're only "calling" the
  // function here (telling it to run). The actual function code
  // is further down in the sketch.

  mainColors();

  // The above function turns the individual LEDs full-on and
  // full-off. If you want to generate more than eight colors,
  // you can do so by varying the brightness of the individual
  // LEDs between full-on and full-off.

  // The analogWrite() function lets us do this. This function
  // lets you dim a LED from full-off to full-on over 255 steps.

  // We've written a function called showSpectrum() that smoothly
  // steps through all the colors. Again we're just calling it
  // here; the actual code is further down in this sketch.

  showSpectrum();
}

// Here's the mainColors() function we've written.

// This function displays the eight "main" colors that the RGB LED
// can produce. If you'd like to use one of these colors in your 
// own sketch, you cancopy and paste that section into your code.

void mainColors()
{
  // Off (all LEDs off):

  digitalWrite(RED_PIN, LOW);
  digitalWrite(GREEN_PIN, LOW);
  digitalWrite(BLUE_PIN, LOW);

  delay(1000);

  // Red (turn just the red LED on):

  digitalWrite(RED_PIN, HIGH);
  digitalWrite(GREEN_PIN, LOW);
  digitalWrite(BLUE_PIN, LOW);

  delay(1000);

  // Green (turn just the green LED on):

  digitalWrite(RED_PIN, LOW);
  digitalWrite(GREEN_PIN, HIGH);
  digitalWrite(BLUE_PIN, LOW);

  delay(1000);

  // Blue (turn just the blue LED on):

  digitalWrite(RED_PIN, LOW);
  digitalWrite(GREEN_PIN, LOW);
  digitalWrite(BLUE_PIN, HIGH);

  delay(1000);

  // Yellow (turn red and green on):

  digitalWrite(RED_PIN, HIGH);
  digitalWrite(GREEN_PIN, HIGH);
  digitalWrite(BLUE_PIN, LOW);

  delay(1000);

  // Cyan (turn green and blue on):

  digitalWrite(RED_PIN, LOW);
  digitalWrite(GREEN_PIN, HIGH);
  digitalWrite(BLUE_PIN, HIGH);

  delay(1000);

  // Purple (turn red and blue on):

  digitalWrite(RED_PIN, HIGH);
  digitalWrite(GREEN_PIN, LOW);
  digitalWrite(BLUE_PIN, HIGH);

  delay(1000);

  // White (turn all the LEDs on):

  digitalWrite(RED_PIN, HIGH);
  digitalWrite(GREEN_PIN, HIGH);
  digitalWrite(BLUE_PIN, HIGH);

  delay(1000);
}

// Below are two more functions we've written,
// showSpectrum() and showRGB().

// showRGB() displays a single color on the RGB LED.
// You call showRGB() with the number of a color you want
// to display.

// showSpectrum() steps through all the colors of the RGB LED,
// displaying a rainbow. showSpectrum() actually calls showRGB()
// over and over to do this.

// We'll often break tasks down into individual functions like
// this, which makes your sketches easier to follow, and once
// you have a handy function, you can reuse it in your other
// programs.

// showSpectrum()

// This function steps through all the colors of the RGB LED.
// It does this by stepping a variable from 0 to 768 (the total
// number of colors), and repeatedly calling showRGB() to display
// the individual colors.

// In this function, we're using a "for() loop" to step a variable
// from one value to another, and perform a set of instructions
// for each step. For() loops are a very handy way to get numbers
// to count up or down.

// Every for() loop has three statements separated by semicolons:

//   1. Something to do before starting

//   2. A test to perform; as long as it's true,
//      it will keep looping

//   3. Something to do after each loop (usually
//      increase a variable)

// For the for() loop below, these are the three statements:

//   1. x = 0;     Before starting, make x = 0.

//   2. x < 768;   While x is less than 768, run the
//                 following code.

//   3. x++        Putting "++" after a variable means
//                 "add one to it". (You can also use "x = x + 1")

// Every time you go through the loop, the statements following
// the loop (those within the brackets) will run.

// And when the test in statement 2 is finally false, the sketch
// will continue.

void showSpectrum()
{
  int x;  // define an integer variable called "x"

  // Now we'll use a for() loop to make x count from 0 to 767
  // (Note that there's no semicolon after this line!
  // That's because the for() loop will repeat the next
  // "statement", which in this case is everything within
  // the following brackets {} )

  for (x = 0; x < 768; x++)

  // Each time we loop (with a new value of x), do the following:

  {
    showRGB(x);  // Call RGBspectrum() with our new x
    delay(10);   // Delay for 10 ms (1/100th of a second)
  }
}

// showRGB()

// This function translates a number between 0 and 767 into a
// specific color on the RGB LED. If you have this number count
// through the whole range (0 to 767), the LED will smoothly
// change color through the entire spectrum.

// The "base" numbers are:
// 0   = pure red
// 255 = pure green
// 511 = pure blue
// 767 = pure red (again)

// Numbers between the above colors will create blends. For
// example, 640 is midway between 512 (pure blue) and 767
// (pure red). It will give you a 50/50 mix of blue and red,
// resulting in purple.

// If you count up from 0 to 767 and pass that number to this
// function, the LED will smoothly fade between all the colors.
// (Because it starts and ends on pure red, you can start over
// at 0 without any break in the spectrum).

void showRGB(int color)
{
  int redIntensity;
  int greenIntensity;
  int blueIntensity;

  // Here we'll use an "if / else" statement to determine which
  // of the three (R,G,B) zones x falls into. Each of these zones
  // spans 255 because analogWrite() wants a number from 0 to 255.

  // In each of these zones, we'll calculate the brightness
  // for each of the red, green, and blue LEDs within the RGB LED.

  if (color = 512       // zone 3
  {
    redIntensity = (color - 512);         // red off to on
    greenIntensity = 0;                   // green is always off
    blueIntensity = 255 - (color - 512);  // blue on to off
  }

  // Now that the brightness values have been set, command the LED
  // to those values

  analogWrite(RED_PIN, redIntensity);
  analogWrite(BLUE_PIN, blueIntensity);
  analogWrite(GREEN_PIN, greenIntensity);
}

Code to slowly fade from one random color to another:

// This program blends smoothly (linearly)
// from one random color, to another, 
// over the course of a period of 1000 milliseconds

const int RED_PIN   = 9;
const int GREEN_PIN = 10;
const int BLUE_PIN  = 11;

int rp,gp,bp; // the P (previous) color
int rn,gn,bn; // the N (next) color

int prevChangeTime;
int period = 1000;

//---------------------------------------------
void setup() {
  pinMode (RED_PIN,   OUTPUT);
  pinMode (GREEN_PIN, OUTPUT);
  pinMode (BLUE_PIN,  OUTPUT);
  
  prevChangeTime = 0;
  int rp = random (0,255);
  int gp = random (0,255);
  int bp = random (0,255);
  int rn = random (0,255);
  int gn = random (0,255);
  int bn = random (0,255);
}

//---------------------------------------------
void loop() {

  int curTime = millis();
  int elapsed = curTime - prevChangeTime;
 
  if (elapsed > period){ 
	prevChangeTime = curTime; 
	rp = rn;
	gp = gn;
	bp = bn;
	rn = random (0,255);
	gn = random (0,255);
	bn = random (0,255);
  }
  
  int rc = map (elapsed, 0, period, rp, rn);
  int gc = map (elapsed, 0, period, gp, gn);
  int bc = map (elapsed, 0, period, bp, bn);
  
  analogWrite (RED_PIN,   rc);  
  analogWrite (GREEN_PIN, gc); 
  analogWrite (BLUE_PIN,  bc); 
}
Comments Off on 09c. Blinking LEDs Posted in

09a. Your Arduino Kit

Download the intro to Arduino comic from here

Your Arduino kits have been designed and provided by Ben Peoples of BirdBrain Labs, Pittsburgh’s very own travelling Arduino salesman. The kits consist of a Sparkfun Inventor’s Kit base, along with a small handful of extra goodies. The total cost will be just about exactly $100:

Sparkfun Inventor’s Kit (SIK):

Birdbrain Labs Enhancements:

  • 0.5” Diameter FSR
  • Tilt ball switch
  • Slide Potentiometer w/ leads & Knob
  • 1:120 Gearhead motor w/ 3mm D-shaft & leads
  • 2-position toggle switch (On-On) with leads
  • Hall Effect Sensor
  • Nice potentiometer
  • Big Red Button
  • (2) 12” M-F 1×6 Extensions
  • (3) 20” alligator clips
  • TIP120 5A Transistor

Teaching Kit Enhancements:

  • 3-axis Analog Accelerometer w/ headers installed
  • Sharp IR distance sensor
Comments Off on 09a. Your Arduino Kit Posted in